Computational Modeling of Metal Toe Caps to Reinforce Safety Footwear: A Finite Element Approach
DOI:
https://doi.org/10.38032/scse.2025.3.121Keywords:
Toe cap, Fluting, Safety footwear, Deformation analysis, Finite element analysisAbstract
Toe caps in safety footwear improve protection against workplace injuries, and the commonly used toe cap materials are metal, plastic, and composite. Metal is used to strengthen the toe cap; however, increased thickness proportionally adds weight to the shoe. Adding flutings can strengthen the toe cap rather than increase the thickness, and a study is required to evaluate the impact of fluting height and direction on the strength of the toe cap. The objectives of this study were to optimize the strength of the toe caps by applying flutings along different directions with various fluting heights and toe cap materials. Toe caps with no flutings, longitudinal flutings, and transverse flutings were the three types of samples used to evaluate deformation. For both longitudinal and transverse directions, the heights of 2 mm, 3 mm, and 4 mm flutings were added to the toe cap surface, and those models of the toe caps were developed by SolidWorks software. Ansys software performed finite element analyses of all the toe cap models for different materials (steel, aluminum, titanium). The strength of the toe cap was determined through deformation analysis by applying a load to the surface. Compared to longitudinally fluted toe caps, transversely fluted toe caps displayed a lower deformation in this test. Furthermore, the 4 mm steel transverse fluted toe cap showed less deformation than the 2 mm and 3 mm steel transverse fluted toe caps. Moreover, steel has the lowest rate of deformation among the three materials. Therefore, the toe cap with 4 mm transverse flutings was considered the strongest among the analyzed toe cap models. This study may be helpful for footwear manufacturers to produce stronger toe caps for safety footwear for workers who need to carry heavy-weight objects in their workplace.
Downloads
Downloads
Downloads
References
[1] Brinker, K., Jacobs, T., Shire, J., Bunn, T., Chalmers, J., Dang, G., Flammia, D., Higgins, S., Lackovic, M., Lavender, A. and Lewis, J. S., Fatal Work-Related Injuries: southeastern United States, 2008-2011. Workplace Health & Safety, vol. 64, pp. 135-140, 2016.
[2] Kearney, G. D. and Imai, S., Occupational fatalities among grounds maintenance workers in the United States (2016− 2020). American Journal of industrial medicine, vol. 66, pp. 750-758, 2023.
[3] https://ec.europa.eu/eurostat/web/products-eurostat-news/w/ddn-20240426-1 (October 24, 2024)
[4] Giri, S., Adhikari, A., Khanal, A., Chipalu, P., Aryal, P. and Pandey, P., Usage of personal protective equipment by patient care nurses to reduce occupational health risk: Challenges and related policy measures in Nepal. Journal of Multidisciplinary Research Advancements, vol. 1, pp. 12-20, 2023.
[5] Costa, S. L., Mendonça, J. P. and Peixinho, N., Study on the impact behaviour of a new safety toe cap model made of ultra-high-strength steels. Materials & Design, vol. 91, pp. 143-154, 2016.
[6] Rodrigues, P. V., Ramoa, B., Machado, A. V., Cardiff, P. and Nóbrega, J M., Assessing the compressive and impact behavior of plastic safety toe caps through computational modelling. Polymers, vol. 13, pp. 4332, 2021.
[7] Yao, B., Kuznetsov, V .L., Xiao, T., Slocombe, D. R., Rao, C. N. R., Hensel, F. and Edwards, P. P., Metals and non-metals in the periodic table. Philosophical Transactions of the Royal Society A, vol. 378, pp. e20200213, 2020.
[8] Rahmzadeh, A., Ghassemieh, M., Park, Y. and Abolmaali, A., Effect of stiffeners on steel plate shear wall systems. Steel and composite structures, vol. 20, pp. 545-569, 2016.
[9] Lu, J. F., Jin, L. L., Yang, X. D. and Sun, D., Design and Analysis on Stiffeners of Coal Mine Rescue Capsules. Applied Mechanics and Materials, vol. 143, pp. 443-447, 2012.
[10] Peixinho, N., Costa, S. and Mendonça, J., Experimental and Numerical Assessment of the Impact Test Performance Between Two UHSS Toe Cap Models. Materials Research, vol. 25, pp. e20220167, 2022.
[11] Costa, S. L., Mendonça, J. P. and Peixinho, N., Numerical simulation of quasi-static compression behavior of the toe cap component for safety footwear. International Journal of Computer Theory and Engineering, vol. 6, pp. 285, 2014.
[12] Pavlackova, J., Egner, P., Mokrejs, P. and Cernekova, M., Verification of toe allowance of children’s footwear and its categorisation. Footwear Science, vol. 7, pp. 149-157, 2015.
[13] Stanier, S. A., Blaber, J., Take, W. A. and White, D. J., Improved image-based deformation measurement for geotechnical applications. Canadian Geotechnical Journal, vol. 53, pp. 727-739, 2016.
Song, Y., Shao, E., Bíró, I., Baker, J. S. and Gu, Y., Finite element modelling for footwear design and evaluation: A systematic scoping review. Heliyon, vol. 8, 2022.
[14] Costa, S. L., Peixinho, N. and Mendonça, J. P., Numerical simulation of impact events of the ultimate
metallic toe cap model for safety footwear. In: ASME International Mechanical Engineering Congress and Exposition, Int. Conf. American Society of Mechanical Engineers, November, 2014.
[15] Yang CC, Duhovic M, Lin RJ, Bhattacharyya D. Finite element modelling and analysis of composites toecaps. InIOP Conference Series: Materials Science and Engineering.IOP Publishing. Vol. 4, No. 1, p. 012010, 1 Aug 2009.
[16] Campbell, S. D., A comparative strength study of metal ceramic and all-ceramic esthetic materials: modulus of rupture. The Journal of Prosthetic Dentistry, vol 62, pp. 476-479, 1889.
[17] Bolzoni, L., Herraiz, E., Ruiz-Navas, E. M. and Gordo, E., Study of the properties of low-cost powder metallurgy titanium alloys by 430 stainless steel addition. Materials & Design, vol. 60, pp. 628-636, 2014.
[18] Miyagawa, K., Tsubaki, M., Yasui, T., Fukumoto, M., Spot welding between aluminium alloy and Zn-coated steel by friction stirring. Welding International, vol. 23, pp. 648-653., 2009.
[19] Boyer, R. R., Design properties of a high-strength titanium alloy, Ti-10V-2Fe-3Al. The Journal of The Minerals,Metals & Materials Society, vol. 32, pp. 61-65, 1980.
Published
Conference Proceedings Volume
Section
License
Copyright (c) 2025 Md. Imrul Kayes Limon, Hanjala Tahmid, Tatini Goswami, Md Istiaq Mahmud Tanvir, Shihab Ahemed (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
All the articles published by this journal are licensed under a Creative Commons Attribution 4.0 International License
