An Intelligent Industrial Safety and Health Monitoring System for Industry 4.0

Authors

  • Prangon Das Department of Mechatronics Engineering, Rajshahi University of Engineering & Technology, Rajshahi-6204, Bangladesh
  • Sarafat Hussain Abhi Department of Mechatronics Engineering, Rajshahi University of Engineering & Technology, Rajshahi-6204, Bangladesh
  • F I Z Suhreed Department of Mechatronics Engineering, Rajshahi University of Engineering & Technology, Rajshahi-6204, Bangladesh
  • Jalal Uddin Department of Mechatronics Engineering, Rajshahi University of Engineering & Technology, Rajshahi-6204, Bangladesh
  • Shahriar Jahan Department of Mechatronics Engineering, Rajshahi University of Engineering & Technology, Rajshahi-6204, Bangladesh
  • Roknuz Zaman Department of Mechatronics Engineering, Rajshahi University of Engineering & Technology, Rajshahi-6204, Bangladesh
  • Md Abul Kashem Department of Mechatronics Engineering, Rajshahi University of Engineering & Technology, Rajshahi-6204, Bangladesh

DOI:

https://doi.org/10.38032/scse.2025.2.1

Keywords:

Exhaust Gas Recirculation, Diesel-Gasoline Dual Fuel CI Engine, Combustion and Emission Performance

Abstract

Due to the depletion of Diesel fuel and higher cost, it is desirable to find alternative fuel with lower cost and better combustion and emission characteristics. As, gaseous fuel is cheaper than liquid fuel, one of the effective solutions to obtain better engine performance is replacing a portion of liquid fuel by gaseous fuel in CI engine which is called dual fuel CI engine. In dual fuel engine, main gaseous fuel is provided through intake manifold by premixing with air and the mixture is ignited by injecting liquid pilot fuel at near the end of the compression stroke. The process is cost effective as well as the engine obtain higher thermal efficiency and lower soot, CO, UHC emission. But NOx emission is increased in CI engine with dual fuel mode which adversely affected the human health and pollute the environment. By applying Exhaust Gas Recirculation (EGR), NOx emission and knocking of the engine can be reduced. In this numerical simulation, the effect of EGR on combustion and emission performance of dual fuel CI is investigated through ANSYS Forte 18.1. In this study, gasoline is considered as main gaseous fuel and diesel is considered as liquid pilot fuel. Effect of EGR on various engine parameters such as in-cylinder pressure, temperature, heat release rate, ignition delay, combustion duration, NOx, CO and UHC emission is investigated. It is seen that, in-cylinder peak pressure is reduced to 50.65% and in-cylinder maximum temperature is reduced to 60.19% for the addition of 40% EGR. NOx emission is reduced to 57.19% for the addition of 10% EGR, 21.32% for 20% EGR, 1.57% for 30% EGR and 0.014% for 40% EGR.

Downloads

Downloads

Downloads

Download data is not yet available.

References

[1] L. Huang, Q. Fu, M. He, D. Jiang, and Z. Hao, "Detection algorithm of safety helmet wearing based on deep learning," Concurrency and Computation: Practice and Experience, vol. 33, no. 13, p. e6234, 2021. DOI: https://doi.org/10.1002/cpe.6234

[2] A. H. Rubaiyat, T. T. Toma, M. Kalantari-Khandani, S. A. Rahman, L. Chen, Y. Ye, and C. S. sconstruction safety," in 2016 IEEE/WIC/ACM International Conference on Web Intelligence Workshops (WIW). IEEE, 2016, pp. 135-142. DOI: https://doi.org/10.1109/WIW.2016.045

[3] A. Afkhamiaghd and E. Elwakil, "Preliminary modeling of coronavirus (covid-19) spread in construction industry." Journal of emergency management (Weston, Mass.), vol. 18, no. 7, pp. 9-17, 2020. DOI: https://doi.org/10.5055/jem.2020.0481

[4] T. Alhmiedat et al., "A survey on environmental monitoring systems using wireless sensor networks." J. Networks, vol. 10, no. 11, pp. 606- 615, 2015. DOI: https://doi.org/10.4304/jnw.10.11.606-615

[5] F. Chen and J. Ma, "An empirical identification method of gaussian blur parameter for image deblurring," IEEE Transactions on signal processing, vol. 57, no. 7, pp. 2467-2478, 2009. DOI: https://doi.org/10.1109/TSP.2009.2018358

[6] S. Du, M. Shehata, and W. Badawy, "Hard hat detection in video sequences based on face features, motion and color information," in 2011 3rd international conference on computer research and development, vol. 4. ieee, 2011, pp. 25-29. DOI: https://doi.org/10.1109/ICCRD.2011.5763846

[7] R. Lienhart and J. Maydt, "An extended set of haar-like features for rapid object detection," in Proceedings. international conference on image processing, vol. 1. IEEE, 2002, pp. I-I. DOI: https://doi.org/10.1109/ICIP.2002.1038171

[8] C.-Y. Wen, S.-H. Chiu, J.-J. Liaw, and C.-P. Lu, "The safety helmet detection for atm's surveillance system via the modified hough transform," in IEEE 37th Annual 2003 International Carnahan Conference on Security Technology, 2003. Proceedings. IEEE, 2003, pp. 364-369.

[9] M. S. Ejaz, M. R. Islam, M. Sifatullah, and A. Sarker, "Implementation of principal component analysis on masked and non-masked face recognition," in 2019 1st international conference on advances in science, engineering and robotics technology (ICASERT). IEEE, 2019, pp. 1-5. DOI: https://doi.org/10.1109/ICASERT.2019.8934543

[10] S. E. Eikenberry, M. Mancuso, E. Iboi, T. Phan, K. Eikenberry, Y. Kuang, E. Kostelich, and A. B. Gumel, "To mask or not to mask: Modeling the potential for face mask use by the general public to curtail the covid-19 pandemic," Infectious disease modelling, vol. 5, pp. 293-308, 2020. DOI: https://doi.org/10.1016/j.idm.2020.04.001

[11] C.-B. Jin, S. Li, and H. Kim, "Real-time action detection in video surveillance using sub-action descriptor with multi-cnn," arXiv preprint arXiv:1710.03383, 2017.

Published

08.05.2025

How to Cite

[1]
P. Das, “An Intelligent Industrial Safety and Health Monitoring System for Industry 4.0”, SCS:Engineering, vol. 2, pp. 1–4, May 2025, doi: 10.38032/scse.2025.2.1.

Similar Articles

1-10 of 111

You may also start an advanced similarity search for this article.